Residential decorative concrete

Since 1989, one slab at a time.

Exposed aggregate, floating steps, slate and coloured finishes for homes across south-east Melbourne and the Mornington Peninsula. Formed properly, poured once, and still square in ten years.

What we build

Five finishes and the walls that hold them up. Bring us a photo of something you like and we'll tell you what it is and what it costs.

Exposed aggregate

Exposed aggregate

Surface washed back to reveal the stone. Grippy underfoot, hides marks, and no two driveways look identical.

Best for: driveways, pool surrounds
Coloured

Coloured concrete

Oxide through the mix rather than on top, so chips and wear don't show a grey layer underneath.

Best for: matching brickwork or render
Honed / polished

Honed / polished

Ground back to a smooth, low-sheen face. The sharpest looking option and the one that shows off good formwork.

Best for: entries, floating steps
Slate

Slate finish

A slate texture pressed into the surface while it's still wet. Reads like laid stone, but it's one continuous slab — nothing to lift, shift or grow weeds through.

Best for: patios, pool surrounds, driveways
Plain, stipple & broom

Plain, stipple & broom

Straightforward and hard-wearing, and the cheapest per square metre. Stipple or a broom finish adds grip where it slopes or gets wet.

Best for: paths, sheds, side access
Retaining walls

Retaining walls

Precast concrete panels set between steel posts, installed to hold a sloping block. Drainage behind the wall matters as much as the wall itself — that's where they fail.

Best for: sloping blocks, split levels, driveway edges
What we're known for

Floating steps

Floating steps are the first thing people see coming up to a house, and the hardest thing to fix if they're not right. Each tread is steel reinforced and tied back into the footing. A few millimetres out on one throws the whole flight. Slow work, and the part we're fussiest about.

StructureSteel reinforced and tied back into the footing or wall — not stacked blocks with a render coat.
The revealConsistent shadow gap set at the form stage and checked on every tread before the pour.
Finish optionsHoned, exposed aggregate or coloured, with a bullnose or square nose to suit the house.
Lead timeFormwork and pour typically run across several days, then curing before you walk on them.

How a job runs

Four stages, in order. You'll know which one we're up to.

01

Site visit and quote

We measure up, check access for the truck and the fall for drainage, then quote a fixed price with the finish written on it.

02

Prep and formwork

Excavation, compacted base, formwork set to line and level, and reinforcement tied. This stage decides how the finished job looks.

03

Pour and finish

Concrete placed, screeded and worked to the finish you chose. Exposed aggregate gets washed back once the surface has gone off enough.

04

Cuts, seal and clean up

Expansion cuts in, sealer applied where it's needed, formwork and spoil taken away. We tell you when it's right to drive on.

Recent work

Photos from our own jobs — no stock images.

Honed aggregate step
Honed aggregate step
Floating steps with under-tread lighting
Floating steps
Stamped slate-pattern paving
Slate finish
Close-up of exposed aggregate texture
Exposed aggregate — close up
Charcoal coloured concrete footpath and entry
Charcoal footpath
Precast concrete panel retaining wall
Precast retaining wall

Get a quote

Send through the address and rough size and we'll come and look. Photos or a video of the site help — text them straight to 0431 564 879 if that's easier.

Or get us direct

Phone
0431 564 879
Email
kkconcreteptyltd@hotmail.com
Hours
9am – 5pm

Areas we cover

South-east Melbourne

BentleighOrmondBrightonHamptonBeaumarisCarnegieChadstoneOakleighHuntingdaleCamberwellBalwynMount WaverleyGlen WaverleyWheelers Hill

Mornington Peninsula

MorningtonMount ElizaMount MarthaSafety BeachDromana

Nearby suburbs too — just ask.